Suppose you have bought a fine guitar with a lovely sound and are learning to play it. But after a while, you notice that it has gone slightly out of tune. What do you do? Learn how to tune it, or trade it in for a piano? Enter the importance of learning how to align your Newtonian reflector telescope.
Your Newtonian reflector will give great images of stars and planets — but only as long as you keep it well tuned. The "tuning" of a telescope is known as collimation. You may have heard that it is incomprehensible, tedious, time-consuming, a pain in the neck, and best avoided. I hope to convince you that it is none of these things. You can master it and in only a minute or two get your instrument ready for a star performance.
Know Your Newtonian Reflector Telescope
If you aren't already acquainted with the optical parts of your telescope, now is the time. Here are the components that you will be lining up:
The Primary Mirror
This is the paraboloidal mirror at the bottom of the tube. It has an aluminized surface that reflects starlight to form an image at the focal plane. The important thing to know that it has an axis of symmetry — the optical axis. On this axis, at the focal point, is a "sweet spot" where images of stars and planets are as sharp and crisp as they can be. Outside the sweet spot, an aberration known as coma visibly degrades the image. Coma makes stars appear asymmetric even if the telescope is perfectly focused — the farther the star is from the center of the focal plane, the worse it gets. In particular, this aberration can dramatically reduce the clarity of planetary detail.
Surprisingly, the size of the "sweet spot" depends only on the main mirror's focal ratio (the mirror's focal length divided by its diameter) and not its size. For instance, even a perfect f/4.5 mirror, small or large, can provide "diffraction limited" performance only within a 2-millimeter (0.08-inch) circle at the focal plane. An f/10 paraboloid's sweet spot, by contrast, spans 22 mm (0.87 inch). (For the mathematically inclinded, the sweet spot's diameter is proportional to the cube of the f/ratio.)
The primary mirror is held in an adjustable cell designed to support the mirror without deforming it. By adjusting the cell's collimation screws we can fine-tune the mirror's tilt and accurately position the sweet spot where we want it. Because the sweet spot can be very small, this is by far the most critical part of collimation. Have a look at your telescope and make sure you know where these adjustment screws are and how they work.To make collimation easy, the center of the mirror should be marked in some way. I recommend marking it with a piece of electrician's tape. Don't make it too small — a ½-inch-diameter (or even slightly larger) spot works well. As long as it is smaller than your diagonal mirror, it will not affect your telescope's performance. If you plan to use a laser collimator, make a hole in the center of your spot. (Another approach is to use an adhesive binder reinforcement ring, the kind used by generations of school children to keep their homework from flying out of their 3-ring binders.)
The Secondary Mirror
This is a small, flat mirror that serves to move the image formed by the primary to the side of the tube, where it is viewed with an eyepiece. To minimize harmful diffraction effects, the secondary, or diagonal, mirror is generally only large enough to let the central portion of the focal plane receive light from the whole primary mirror. You should center this fully illuminated area in the eyepiece by positioning the secondary in the correct location.
The secondary is attached to an adjustable holder suspended on a spider — often a cross made from thin sheet metal. Identify the adjustment screws for the secondary holder and the spider.
The third optical component in the telescope system is the eyepiece. It is a complex magnifying lens used to view the image formed at the focal plane. Like the primary mirror, the eyepiece has an optical axis, and this axis should be aimed at the center of the main mirror for best performance — though in practice it is the center axis of the focuser drawtube that you aim at the primary mirror.
A good eyepiece will render a sharp image in the central parts of the field of view (its sweet spot), but toward the edge not even the best and most expensive eyepieces can produce a perfect image. For this reason it is important to make sure that the sweet spots of the primary mirror and the eyepiece match up — the ultimate goal of collimation.
Now that you know what you're dealing with, look into the empty focuser and try to identify the optical parts just described. This is best done during daylight, with the reflector telescope aimed at the ceiling or the sky (be careful to avoid the Sun). The illustration to the right shows what you should see: the secondary mirror in its holder, its elliptical face tilted 45° and appearing circular. With your eye close to the focuser, you can see the primary mirror reflected in the secondary, and the secondary and its spider in turn reflected in the primary. Finally, inside this reflection of the secondary, you can see the focuser drawtube and your eye.
3 Easy Steps on Aligning Your Newtonian Reflector Telescope
Once you are acquainted with the reflector telescope's optical parts and what they look like in the focuser, you're ready to proceed. To get your telescope well collimated, here is what you need to accomplish:
- Step 1: Center the secondary mirror on the axis of the focuser drawtube.
- Step 2: Aim the eyepiece at the center of the primary mirror.
- Step 3: Center your primary mirror's sweet spot in the eyepiece's field of view.
In most cases, only the last of these three steps will need to be repeated regularly; the first two are more or less set-and-forget operations.
Now let's get to the nuts and bolts of actually collimating your reflector.Step 1: Begin by making sure that the focuser and the secondary are lined up. The simplest and best tool for this step is a sight tube. You slide it into the focuser, as you would an eyepiece, and look through the tube's peephole at the secondary. (If the secondary is far out of adjustment, you should first tilt and/or rotate it to get the reflection of the spot on the primary roughly centered in the sight tube before you proceed.) It may be difficult to distinguish the edge of the secondary from the reflected edge of the main mirror, so place a piece of white cardboard between the secondary mirror and the primary, as shown here.The elliptical secondary should appear round and well centered in the circular opening of the sight tube. If it is, Step 1 is done. If not, either the secondary holder or the focuser (or both) needs attention.Try adjusting the secondary holder first. You can usually move it toward or away from the primary by adjusting the center bolt that joins the holder to the spider.
If the error is toward either side of the sight tube (90° to the optical axis), also check to find out if the secondary is well centered in the reflector telescope tube. If it isn't, adjust the spider's mounting screws until it is. If this checks out fine, then tilt the focuser by putting shims under its mounting plate.
Step 2: Here you adjust the tilt of the secondary mirror to aim the focuser's axis at the center of the primary. First, remove the cardboard from the spider. Now, while viewing through the sight tube, carefully adjust the screws that tilt and rotate the secondary until the primary mirror's reflection appears centered in your field of view. If your sight tube has cross hairs, align the primary's center spot with them; otherwise, center the outer edge of the primary within the sight tube. (Make sure that the sight tube is racked in far enough to let you see the whole primary mirror.) A laser collimator is even better for this step — just center the laser beam on the primary's center spot.
A small error in secondary alignment is usually not a problem. As long as the pointing error is no more than 1 or 2 percent of the main mirror's diameter, it makes no visible difference. However, if you plan to use a laser collimator in Step 3, you should be aware that even a tiny misadjustment here will throw off the final collimation.
If you have a truss-tube telescope, you will need to repeat Step 2 each time you reassemble the scope. With a solid-tube reflector, you need only check this once in a while.
Step 3: In this, the final and most critical step, you need to tilt the main mirror to center its sweet spot (and its optical axis) in the focuser. This procedure should be done at the beginning of each observing session and checked occasionally during the night, since temperature changes or routine handling may cause your reflector telescope's components to shift enough to change collimation.
The best tool for this procedure is a Cheshire eyepiece. Put it in the focuser and observe the reflection of its shiny 45°-angle face in the primary. By turning the primary's adjustment screws you can move this reflection until it appears centered on the primary mirror's center spot. If you can make these adjustments while looking in the Cheshire, so much the better; otherwise an assistant can be very helpful. Most mirror cells have three adjustment screws or three pairs of push-pull adjustments. For simplicity's sake, I recommend using only two of the adjustments — the third one (which might as well be the one that is hardest to reach) can be left alone unless you run out of adjustment on one of the others.
When Step 3 is done, the optical axis is accurately centered in the focuser, and collimation is complete. However, if you look carefully you will notice that the Cheshire eyepiece does not appear exactly centered inside the shadow of the secondary. Don't worry; this is in fact how things should look because the secondary mirror is slightly offset. But bear in mind that you needn't master the somewhat elliptical reasoning behind the subject in order to collimate your reflector telescope well!)
A laser collimator is often used for Step 3, by centering the returning beam on the laser's faceplate. However, this method has problems that belie the laser's presumed accuracy. Why? Suppose that in Step 2 the laser beam has missed the true center of the primary mirror by a small distance, for example, 2 mm. Even if the primary mirror happens to be exactly collimated (its center precisely aligned with the center of the eyepiece), the returning laser beam will be parallel to the main mirror's axis but will miss the center of the laser faceplate by 2 mm. If you then tilt the main mirror to center the beam returning to the laser, the collimation will be 1 mm off! Unintentionally, you will have caused a miscollimation great enough to affect the performance of a short-focal-length telescope. This extreme sensitivity to a small and otherwise unimportant error in Step 2 is the Achilles' heel of the laser collimator. So even if you use one for rough alignment in Step 3, it is better to use a Cheshire eyepiece for the final adjustment.
Star-Testing Your CollimationOnce your reflector telescope has cooled down and is well-collimated, it should be ready to perform at its best. At high magnification (25× to 50× per inch of aperture, or 1× to 2× per mm of aperture) and in good seeing conditions, stars at focus should appear in the eyepiece as tight, symmetric diffraction disks. However, if stars at the center of the field show the telltale asymmetry of coma, double-check your collimation with the Cheshire eyepiece. If the center spot still looks centered, then it isn't located at the primary's true optical center. If this is the case with your mirror's center spot, ignore it for now and try tweaking the primary's collimation, in small steps, until you have centered the best image in the field of view. (This method was described in detail in the June 2001 issue of Sky & Telescope, page 125, and is illustrated below.) The Cheshire will now indicate the location of the primary mirror's true optical center. If necessary, move the spot to the correct position or put another, larger piece of tape on top of it.
If you know that your primary mirror spot is okay (and in most cases it will be, if carefully centered), there is no need to routinely fine-tune your collimation with a star test — the Cheshire eyepiece is not only easier to use, but it is more accurate if the seeing is less than ideal, which it is most nights.
Now your reflector telescope is in perfect tune, and the improvement in performance should be obvious. If not, try to deliberately miscollimate the primary, and see what it does to a high-magnification view of a planet. After this demonstration, you'll never let your scope go out of collimation again.
For more in-depth articles on understanding your equipment and learning your way around the night sky, subscribe to Sky & Telescope.